[2-02-02].第03节:环境搭建 - Win10搭建ES集群环境

发布于:2025-07-10 ⋅ 阅读:(18) ⋅ 点赞:(0)

ElasticSearch学习大纲


基于ElasticSearch7.8版本


一、ElasticStack下载:


二、集群搭建:

第1步:创建es目录:

  • 1.创建 elasticsearch-cluster 文件夹,在内部复制三个 elasticsearch 服务
    在这里插入图片描述

第2步:更改配置:

修改集群文件目录中每个节点的 config/elasticsearch.yml 配置文件

  • node-1001 节点
    #节点 1 的配置信息:
    #集群名称,节点之间要保持一致
    cluster.name: my-elasticsearch
    #节点名称,集群内要唯一
    node.name: node-1001
    node.master: true
    node.data: true
    #ip 地址
    network.host: localhost
    #http 端口
    http.port: 1001
    #tcp 监听端口
    transport.tcp.port: 9301
    discovery.seed_hosts: ["localhost:9301", "localhost:9302","localhost:9303"]
    discovery.zen.fd.ping_timeout: 1m
    discovery.zen.fd.ping_retries: 5
    #集群内的可以被选为主节点的节点列表
    cluster.initial_master_nodes: ["node-1", "node-2","node-3"]
    #跨域配置
    #action.destructive_requires_name: true
    http.cors.enabled: true
    http.cors.allow-origin: "*"
    
  • node-1002 节点
    #节点 2 的配置信息:
    #集群名称,节点之间要保持一致
    cluster.name: my-elasticsearch
    #节点名称,集群内要唯一
    node.name: node-1002
    node.master: true
    node.data: true
    #ip 地址
    network.host: localhost
    #http 端口
    http.port: 1002
    #tcp 监听端口
    transport.tcp.port: 9302
    discovery.seed_hosts: ["localhost:9301"]
    discovery.zen.fd.ping_timeout: 1m
    discovery.zen.fd.ping_retries: 5
    #集群内的可以被选为主节点的节点列表
    #cluster.initial_master_nodes: ["node-1", "node-2","node-3"]
    #跨域配置
    #action.destructive_requires_name: true
    http.cors.enabled: true
    http.cors.allow-origin: "*"
    
  • 3.节点 3 的配置信息:
    #集群名称,节点之间要保持一致
    cluster.name: my-elasticsearch
    #节点名称,集群内要唯一
    node.name: node-1003
    node.master: true
    node.data: true
    #ip 地址
    network.host: localhost
    #http 端口
    http.port: 1003
    #tcp 监听端口
    transport.tcp.port: 9303
    #候选主节点的地址,在开启服务后可以被选为主节点
    discovery.seed_hosts: ["localhost:9301", "localhost:9302"]
    discovery.zen.fd.ping_timeout: 1m
    discovery.zen.fd.ping_retries: 5
    #集群内的可以被选为主节点的节点列表
    #cluster.initial_master_nodes: ["node-1", "node-2","node-3"]
    #跨域配置
    #action.destructive_requires_name: true
    http.cors.enabled: true
    http.cors.allow-origin: "*"
    

第3步:启动节点:

  • 1.启动前先删除每个节点中的 data 目录中所有内容(如果存在)
    在这里插入图片描述
  • 2.分别双击执行 bin/elasticsearch.bat, 启动节点服务器,启动后,会自动加入指定名称的集


网站公告

今日签到

点亮在社区的每一天
去签到