目 录
7.2.3 Xen Center与Xen Server建立连接
7.2.4 在Xen Server中搭建Windows Server 2012
代码呈现：
配置思路和布局：
Sw1:
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys sw1（改名）
[sw1]un in EN（关闭信息提示）
Info: Information center is disabled.
[sw1]VLAN batch 10 20 30 40 50 60 100 101（创建vlan）
[sw1]int Vlanif 10（进入vlan10）
[sw1-Vlanif10]ip ad 192.168.10.254 24（配置IP，做后面配置的网关）
[sw1-Vlanif10]vrrp vrid 10 virtual-ip 192.168.10.252（配置VRRP协议的虚拟IP地址）
[sw1-Vlanif10]q（推出）
[sw1]int Vlanif 20（进入vlan20）
[sw1-Vlanif20]ip address 192.168.20.254 24(配置IP）
[sw1-Vlanif20]vrrp vrid 20 virtual-ip 192.168.20.252（配置虚拟IP）
[sw1-Vlanif20]vrrp vrid 20 priority 120（配置优先级）
[sw1-Vlanif20]vrrp vrid 20 track interface GigabitEthernet 0/0/1（创建监视端口实现快速主备切换）
[sw1-Vlanif20]vrrp vrid 20 track interface GigabitEthernet 0/0/2（创建监视端口实现快速主备切换）
[sw1-Vlanif30]vrrp vrid 30 track interface GigabitEthernet 0/0/1
[sw1-Vlanif30]vrrp vrid 30 track interface GigabitEthernet 0/0/2
[sw1-Vlanif30]q
[sw1]int Vlanif 40
[sw1-Vlanif40]ip ad 192.168.40.254 24
[sw1-Vlanif40]vrrp vrid 40 virtual-ip 192.168.40.252
[sw1-Vlanif40]vrrp vrid 40 priority 120[sw1-Vlanif40]vrrp vrid 40 track interface GigabitEthernet 0/0/1
[sw1-Vlanif40]vrrp vrid 40 track interface GigabitEthernet 0/0/2
[sw1-Vlanif40]q
[sw1]int Vlanif 50
[sw1-Vlanif50]ip ad 192.168.50.254 24
[sw1-Vlanif50]vrrp vrid 50 virtual-ip 192.168.50.252
[sw1-Vlanif50]vrrp vrid 50 track interface GigabitEthernet 0/0/1
[sw1-Vlanif60]q
[sw1]int Vlanif 70
Error: The VLAN does not exist.
[sw1]int Vlanif 100
[sw1-Vlanif100]ip ad 192.168.100.254 24
[sw1-Vlanif100]undo shutdown
Info: Interface Vlanif100 is not shutdown.
[sw1-Vlanif100]
[sw1-Vlanif100]q
[sw1]vlan batch 5 7（创建vlan）
Info: This operation may take a few seconds. Please wait for a moment...done.
[sw1]int Vlanif 5
[sw1-Vlanif5]ip ad 192.168.5.2 24
[sw1-Vlanif5]int vlan7
[sw1-Vlanif7]ip ad 192.168.7.2 24
[sw1-Vlanif7]q
[sw1]int g
[sw1]int GigabitEthernet 0/0/1
[sw1-GigabitEthernet0/0/1]port link-type access （配置接口类型为接入模式）
[sw1-GigabitEthernet0/0/1]port default vlan 5（允许通过vlan5）
[sw1-GigabitEthernet0/0/1]int g
[sw1-GigabitEthernet0/0/1]q
[sw1]int g
[sw1]int GigabitEthernet 0/0/2
[sw1-GigabitEthernet0/0/2]port link-type access
[sw1-GigabitEthernet0/0/2]port default vlan 7
[sw1-GigabitEthernet0/0/2]q
[sw1] User interface con0 is available
[sw1]int e
[sw1]int Eth-Trunk 1（创建链路聚合端口）
[sw1-Eth-Trunk1]port link-type trunk （改为通道模式）
[sw1-Eth-Trunk1]port trunk allow-pass vlan all （允许所有vlan通过）
[sw1-Eth-Trunk1]trunkport GigabitEthernet 0/0/3（加入trunk口）
[sw1-Eth-Trunk1]trunkport GigabitEthernet 0/0/4
[sw1]int g
[sw1]int GigabitEthernet 0/0/5
[sw1-GigabitEthernet0/0/5]port link-type trunk
[sw1-GigabitEthernet0/0/5]port trunk allow-pass vlan all
[sw1-GigabitEthernet0/0/12]int GigabitEthernet 0/0/9
[sw1-GigabitEthernet0/0/8]port trunk pvid vlan 101
[sw1-GigabitEthernet0/0/8]
[sw1]stp en
[sw1]stp enable （配置生成树）
[sw1]stp region-configuration进入生成树配置模式）
[sw1-mst-region]re
[sw1-mst-region]region-name huawei（改名）
[sw1-mst-region]re
[sw1-mst-region]region-name
[sw1-mst-region]revision-level 5（配置生成树的权限）
[sw1-mst-region]instance 1 vlan 10 20 30 100（把vlan划分到实例中）
[sw1-mst-region]instance 2 vlan 40 50 60
[sw1-mst-region]active region-configuration （激活实例）
Info: This operation may take a few seconds. Please wait for a moment...done.
[sw1]stp instance 1 root primary （配置实例的优先级的主次）
[sw1]stp instance 2 root secondary （配置实例的优先级的主次）
[sw1]
Sw2:
[sw2]
[sw2]un in en
[sw2]vlan batch 10 20 30 40 50 60 100 101 6 8（创建vlan）
[sw2]int Vlanif 10
[sw2-Vlanif10]q
[sw2]int Vlanif 20
[sw2-Vlanif20]ip address 192.168.20.253 24
[sw2-Vlanif20]vrrp vrid 20 virtual-ip 192.168.20.252
[sw2-Vlanif20]vrrp vrid 20 track interface GigabitEthernet 0/0/1
[sw2-Vlanif20]vrrp vrid 20 track interface GigabitEthernet 0/0/2
[sw2-Vlanif20]q
[sw2]int Vlanif 30
[sw2-Vlanif30]ip ad 192.168.30.253 24
[sw2-Vlanif30]vrrp vrid 30 virtual-ip 192.168.30.252
[sw2-Vlanif30]vrrp vrid 30 track interface GigabitEthernet 0/0/1
[sw2-Vlanif30]vrrp vrid 30 track interface GigabitEthernet 0/0/2
[sw2-Vlanif30]q
[sw2]int Vlanif 40
[sw2-Vlanif40]ip ad 192.168.40.253 24
[sw2-Vlanif40]vrrp vrid 40 virtual-ip 192.168.40.252
[sw2-Vlanif40]vrrp vrid 40 track interface GigabitEthernet 0/0/1
[sw2-Vlanif40]vrrp vrid 40 track interface GigabitEthernet 0/0/2
[sw2-Vlanif40]q
[sw2]int Vlanif 50
[sw2-Vlanif50]q
[sw2]int Vlanif 40
[sw2-Vlanif40]q
[sw2]int Vlanif 50
[sw2-Vlanif50]ip ad 192.168.50.253 24
[sw2-Vlanif50]vrrp vrid 50 virtual-ip 192.168.50.252
[sw2]int vlna
[sw2]int Vlanif 60
[sw2-Vlanif60]ip ad 192.168.60.253 24
[sw2-Vlanif60]vrrp vrid 60 virtual-ip 192.168.60.252
[sw2-Vlanif60]vrrp vrid 60 priority 120
[sw2-Vlanif60]vrrp vrid 60 track interface GigabitEthernet 0/0/1
[sw2-Vlanif60]vrrp vrid 60 track interface GigabitEthernet 0/0/2
[sw2-Vlanif60]
[sw2-Vlanif60]q
[sw2][sw2-Vlanif60]
[sw2-Vlanif60]q
[sw2]int Vlanif 6
[sw2-Vlanif6]ip ad 192.168.6.2 24
[sw2-Vlanif6]q
[sw2]int Vlanif 8
[sw2-Vlanif8]ip ad 192.168.8.2 24
[sw2-Vlanif8]q
[sw2]int g
[sw2]int GigabitEthernet 0/0/1
[sw2-GigabitEthernet0/0/1]port link-type access
[sw2-GigabitEthernet0/0/1]port default vlan 8
[sw2-GigabitEthernet0/0/1]int g0/0/2
[sw2-GigabitEthernet0/0/2]port link-type access
[sw2-GigabitEthernet0/0/2]port default vlan 6
[sw2-GigabitEthernet0/0/2]q
[sw2]int e
[sw2]int Eth-Trunk
[sw2]int Eth-Trunk 1
[sw2-Eth-Trunk1]port link-type trunk
[sw2-Eth-Trunk1]port trunk allow-pass vlan all
[sw2-Eth-Trunk1]trunkport GigabitEthernet 0/0/3
Info: This operation may take a few seconds. Please wait for a moment...done.
[sw2-Eth-Trunk1]trunkport GigabitEthernet 0/0/4
[sw2-Eth-Trunk1]q
[sw2]int g
[sw2]int GigabitEthernet 0/0/6
[sw2-GigabitEthernet0/0/7]int GigabitEthernet 0/0/5
[sw2-GigabitEthernet0/0/5]port link-type trunk
[sw2-GigabitEthernet0/0/5]port trunk allow-pass vlan all
[sw2-GigabitEthernet0/0/5]int GigabitEthernet 0/0/10
[sw2-GigabitEthernet0/0/10]port link-type trunk
[sw2-GigabitEthernet0/0/10]int GigabitEthernet 0/0/10
[sw2-GigabitEthernet0/0/10]int GigabitEthernet 0/0/9
[sw2-GigabitEthernet0/0/9]port link-type trunk
[sw2-GigabitEthernet0/0/9]port trunk allow-pass vlan all
[sw2-GigabitEthernet0/0/9]int GigabitEthernet 0/0/11
[sw2-GigabitEthernet0/0/11]port link-type trunk
[sw2-GigabitEthernet0/0/11]port trunk allow-pass vlan all
[sw2-GigabitEthernet0/0/11]
[sw2]st
[sw2]stp en
[sw2]stp enable
[sw2]st
[sw2]stp re
[sw2]stp region-configuration
[sw2-mst-region]re
[sw2-mst-region]region-name huawei
[sw2-mst-region]re
[sw2-mst-region]region-name
[sw2-mst-region]instance 1 vlan 10 20 30 100
[sw2]stp instance 1 root secondary
[sw2]stp instance 2 root primary
[sw2]
Sw3:
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys sw3
[sw3]un in en
Info: Information center is disabled.
[sw3]vlan batch vlan 10 20 30 40 50 60 100 101
[sw3]stp enable
[sw3]stp region-configuration
[sw3-mst-region]region-name huawei
[sw3-mst-region]region-name
[sw3-mst-region]revision-level 5
[sw3-mst-region]instance 1 vlan 10 20 30 100
[sw3-mst-region]instance 2 vlan 40 50 60
[sw3-mst-region]active region-configuration
[sw3-mst-region]q
[sw3]int GigabitEthernet 0/0/1
[sw3-GigabitEthernet0/0/1]port link-type trunk
[sw3-GigabitEthernet0/0/1]port trunk allow-pass vlan al
[sw3-GigabitEthernet0/0/1]int g0/0/2
[sw3-Ethernet0/0/1]int e0/0/2
[sw3-Ethernet0/0/2]port link-type access
[sw3-Ethernet0/0/2]port default vlan 10
[sw3-Ethernet0/0/2]q
[sw3]
<Huawei>sys
[Huawei]un in en
[Huawei]sys sw4
[sw4]vlan batch 10 20 30 40 50 60 100 101
Info: This operation may take a few seconds. Please wait for a moment...done.
[sw4]stp enable
[sw4]stp enable
[sw4]stp region-configuration
[sw4-mst-region]region-name huawei
[sw4-mst-region]region-name huawei
[sw4-mst-region]revision-level 5
[sw4-mst-region]instance 1 vlan 10 20 30 100
[sw4-mst-region]instance 2 vlan 40 50 60
[sw4-mst-region]active region-configuration
[sw4-mst-region]display this
[sw4-mst-region]st
[sw4-mst-region]stp re
[sw4-mst-region]q
-[sw4]stp region-configuration
[sw4-mst-region]q
-[sw4]int GigabitEthernet 0/0/1
[sw4-GigabitEthernet0/0/1]port link-type trunk
[sw4-GigabitEthernet0/0/1]port trunk allow-pass vlan all
[sw4-GigabitEthernet0/0/1]int g0/0/2
[sw4-GigabitEthernet0/0/2]port link-type trunk
[sw4-GigabitEthernet0/0/2]port trunk allow-pass vlan all
[sw4-GigabitEthernet0/0/2]q
-[sw4]int Ethernet0/0/1
[sw4-Ethernet0/0/2]port link-type ac
[sw4-Ethernet0/0/2]port default vlan 20
[sw4-Ethernet0/0/2]q
[sw4]q
<sw4>save
Sw5:
The device is running!
<Huawei>
<Huawei>sys
[Huawei]un in en
Info: Information center is disabled.
[Huawei]sys sw5
[sw5]vlan batch 10 20 30 40 50 60 100 101
[sw5]vlan batch 10 20 30 40 50 60 100 101
Info: This operation may take a few seconds. Please wait for a moment...done.
[sw5]stp enable
[sw5]stp region-configuration
[sw5-mst-region]region-name huawei
[sw5-mst-region]revision-level 5
[sw5-mst-region]instance 1 vlan 10 20 30 100
[sw5-mst-region]instance 2 vlan 40 50 60
[sw5-mst-region]active region-configuration
Info: This operation may take a few seconds. Please wait for a moment...done.
[sw5]int GigabitEthernet 0/0/1
[sw5-GigabitEthernet0/0/1]port link-type trunk
[sw5-GigabitEthernet0/0/1]port trunk allow-pass vlan al
[sw5-GigabitEthernet0/0/2]int e0/0/1
[sw5-Ethernet0/0/1]port link-type access
[sw5-Ethernet0/0/1]port default vlan 30
[sw5-Ethernet0/0/1]int e0/0/2
[sw5-Ethernet0/0/2]port link-type access
[sw5-Ethernet0/0/2]port default vlan 30
[sw5-Ethernet0/0/2]
AC1:
The device is running!
<AC6605>sys
Enter system view, return user view with Ctrl+Z.
[AC6605]sys AC1
[AC1]v
[AC1]vl
[AC1]vlan 100 101
^
Error: Too many parameters found at '^' position.
[AC1]vl
[AC1]vlan b
[AC1]vlan batch 100 101
Info: This operation may take a few seconds. Please wait for a moment...done.
[AC1]int v
[AC1]int Vlanif 100
[AC1-Vlanif100]ip ad 192.168.100.1 24
[AC1-Vlanif100]q
[AC1]dhcp enable （开启DHCP功能）
Info: The operation may take a few seconds. Please wait for a moment.done.
[AC1]int v
[AC1]int Vlanif 100（进入vlan100）
[AC1-Vlanif100]dhcp select global （DHCP配置指向全局）
[AC1-Vlanif100]q
[AC1]int v
[AC1]int Vlanif 101
[AC1-Vlanif101]ip ad 192.168.101.1 24（配置IP）
[AC1-Vlanif101]dhcp select interface （DHCP配置指向全局）
[AC1-Vlanif101]q
[AC1]ip poo
[AC1]ip pool v
[AC1]ip pool vlan100（创建地址池）
Info: It is successful to create an IP address pool.
[AC1-ip-pool-vlan100]ga
[AC1-ip-pool-vlan100]ex
[AC1-ip-pool-vlan100]excluded-ip-address 192.168.100.1（配置排除地址）
[AC1-ip-pool-vlan100]q
[AC1-wlan-view]ap-group name ap-huawei（建立AP组创建名字）
Info: This operation may take a few seconds. Please wait for a moment.done.
[AC1-wlan-ap-group-ap-huawei]q
[AC1-wlan-view]re
[AC1-wlan-view]regulatory-domain-profile n
[AC1-wlan-view]regulatory-domain-profile name huawei-domin（指定域管理模块并设置域管理名）
[AC1-wlan-regulate-domain-huawei-domin]cou
[AC1-wlan-regulate-domain-huawei-domin]country-code cn （选择国家代码进行配置设定）
[AC1-wlan-regulate-domain-huawei-domin]country-code CN
Info: The current country code is same with the input country code.
[AC1-wlan-regulate-domain-huawei-domin]q
[AC1-wlan-view]ap-group name ap-huawei（创建ap组命名）
[AC1-wlan-ap-group-ap-huawei]q
[AC1-wlan-view]q
[AC1]capwap source interface Vlanif 101（配置原接口或源地址与AP建隧道）
[AC1]w
[AC1]wl
[AC1]wlan ap
[AC1]wlan
[AC1-wlan-view]ap-id 0 ap-mac 00e0-fc89-0220（ap接入控制，这里是mac认证）
[AC1-wlan-ap-0]ap-id 0 ap-mac 00e0-fc89-0220（配置AP认证模式:离线）
[AC1-wlan-ap-0]ap
[AC1-wlan-ap-0]ap-name area-1（创建AP的名字）
[AC1-wlan-ap-0]ap
[AC1-wlan-ap-0]ap-system-profile
[AC1-wlan-ap-0]ap-group ap-huawei
Warning: This operation may cause AP reset. If the country code changes, it will
clear channel, power and antenna gain configurations of the radio, Whether to c
ontinue? [Y/N]:y
Info: This operation may take a few seconds. Please wait for a moment.. done.
[AC1-wlan-ap-0]
[AC1-wlan-ap-0]q
[AC1-wlan-view]q
[AC1]dis
[AC1]display ap
[AC1]display ap-
[AC1]display ap-g
[AC1]display ap-group
[AC1]display ap all
Total: 1
[AC1]int g
[AC1]int GigabitEthernet 0/0/1（进入接口1）
[AC1-GigabitEthernet0/0/1]port link-type trunk（配置为通道模式）
[AC1-GigabitEthernet0/0/1]port trunk allow-pass vlan all （允许所有vlan通过）
[AC1-GigabitEthernet0/0/1]
[AC1]w
[AC1]wlan
[AC1-wlan-view]se
[AC1-wlan-view]security-profile n
[AC1-wlan-view]security-profile name sec（配置安全模板）
[AC1-wlan-sec-prof-sec]security wpa2 psk pass-phrase huawei@123 aes（配置安全模板的密码）
[AC1-wlan-sec-prof-sec]q
[AC1-wlan-view]ssid-profile name ssid-1（配置SSID模板名称）
[AC1-wlan-ssid-prof-ssid-1]ss
[AC1-wlan-ssid-prof-ssid-1]ssid huawei（配置SSID名称）
Info: This operation may take a few seconds, please wait.done.
[AC1-wlan-ssid-prof-ssid-1]q
[AC1-wlan-view]
[AC1-wlan-view]v
[AC1-wlan-view]venue-name-profile
[AC1-wlan-view]vap-profile n
[AC1-wlan-view]vap-profile name vap-1 （VAP名称）
[AC1-wlan-vap-prof-vap-1]forward-mode tunnel
Info: This operation may take a few seconds, please wait.done.
[AC1-wlan-vap-prof-vap-1]s
[AC1-wlan-vap-prof-vap-1]security-profile se
[AC1-wlan-vap-prof-vap-1]security-profile sec
Info: This operation may take a few seconds, please wait.done.
[AC1-wlan-vap-prof-vap-1]se
[AC1-wlan-vap-prof-vap-1]service-vlan
[AC1-wlan-vap-prof-vap-1]security-profile
[AC1-wlan-vap-prof-vap-1]service-mode
[AC1-wlan-vap-prof-vap-1]service-vlan
[AC1-wlan-vap-prof-vap-1]security-profile
[AC1-wlan-vap-prof-vap-1]ssid-profile ssid-1
Info: This operation may take a few seconds, please wait.done.
[AC1-wlan-vap-prof-vap-1]q[AC1-wlan-view]ap-group name ap-huawei（创建AP组名称）
[AC1-wlan-ap-group-ap-huawei]vap-profile vap-1 wlan 1 radio 0（VAP模板名称）
Info: This operation may take a few seconds, please wait...done.
[AC1-wlan-ap-group-ap-huawei]q
[AC1-wlan-view]q
[AC1]
R2:
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]un in en
Info: Information center is disabled.
[Huawei]sys R2
[R2]int g
[R2]int GigabitEthernet 0/0/0
[R2-GigabitEthernet0/0/0]dis
[R2-GigabitEthernet0/0/0]discardth
[R2-GigabitEthernet0/0/0]disp
[R2-GigabitEthernet0/0/0]display th
[R2-GigabitEthernet0/0/0]display this
[V200R003C00]
#
interface GigabitEthernet0/0/0
#
return
[R2-GigabitEthernet0/0/0]
[R2-GigabitEthernet0/0/0]
[R2-GigabitEthernet0/0/0]q
[R2]int g
[R2]int GigabitEthernet 1/0/0
[R2-GigabitEthernet0/0/0]int g0/0/1
[R2-GigabitEthernet0/0/1]ip ad
[R2-GigabitEthernet0/0/1]ip address 192.168.3.2 24
[R2-GigabitEthernet0/0/1]int g0/0/2
[R2-GigabitEthernet0/0/2]ip address 192.168.8.1 24
[R2-GigabitEthernet0/0/2]
[R2-GigabitEthernet0/0/2]
Sw1:
<sw1>sys
Enter system view, return user view with Ctrl+Z.
[sw1]os
[sw1]ospf 10
[sw1-ospf-10]ar
[sw1-ospf-10]area 0
[sw1-ospf-10-area-0.0.0.0]netw
[sw1-ospf-10-area-0.0.0.0]network 192.168.10.0 0.0.0.255
[sw1-ospf-10-area-0.0.0.0]network 192.168.20.0 0.0.0.255
[sw1-ospf-10-area-0.0.0.0]network 192.168.7.0 0.0.0.255
[sw1-ospf-10-area-0.0.0.0]
[sw1-ospf-10-area-0.0.0.0]
Sw2:
[sw2]os
[sw2]ospf 20
[sw2-ospf-20]ar
[sw2-ospf-20]area 0
[sw2-ospf-20-area-0.0.0.0]netw
[sw2-ospf-20-area-0.0.0.0]network 192.168.10.0 0.0.0.255
[sw2-ospf-20-area-0.0.0.0]network 192.168.20.0 0.0.0.255
[sw2-ospf-20-area-0.0.0.0]network 192.168.30.0 0.0.0.255
[sw2-ospf-20-area-0.0.0.0]
[sw2-ospf-20-area-0.0.0.0]
<sw2>
Sw1配置dhcp:
<sw1>
<sw1>
<sw1>
<sw1>
<sw1>sys
Enter system view, return user view with Ctrl+Z.
[sw1]
[sw1]ip pool vlan10
Info:It's successful to create an IP address pool.
[sw1-ip-pool-vlan10]netw
[sw1-ip-pool-vlan10]network 192.168.10.0 ma
[sw1-ip-pool-vlan10]network 192.168.10.0 mask 24
[sw1-ip-pool-vlan10]g
[sw1-ip-pool-vlan10]gateway-list 192.168.10.252
[sw1-ip-pool-vlan10]dns
[sw1-ip-pool-vlan10]dns-list 114.114.114.114
[sw1-ip-pool-vlan10]ex
[sw1-ip-pool-vlan10]excluded-ip-address 192.168.10.100 192.168.10.150
[sw1-ip-pool-vlan10]dhc
[sw1-ip-pool-vlan10]q
[sw1]int vl
[sw1]int Vlanif 10
[sw1-Vlanif10]dhcp select global
[sw1-Vlanif10]q
[sw1]ip poo
[sw1]ip pool vlan
[sw1]ip pool vlan20
Info:It's successful to create an IP address pool.
[sw1-ip-pool-vlan20]netw
[sw1-ip-pool-vlan20]network 192.168.20.0 ma
[sw1-ip-pool-vlan20]network 192.168.20.0 mask 24
[sw1-ip-pool-vlan20]g
[sw1-ip-pool-vlan20]gateway-list 192.168.20.252
[sw1-ip-pool-vlan20]dns
[sw1-ip-pool-vlan20]dns-list 114.114.114.114
[sw1-ip-pool-vlan20]ex
[sw1-ip-pool-vlan20]excluded-ip-address 192.168.20.100 192.168.20.150
[sw1-ip-pool-vlan20]q
[sw1]int vlan
[sw1]int Vlanif 20
[sw1-Vlanif20]dhcp select global
[sw1-Vlanif20]q
[sw1]
[sw1]ip pool vlan30
Info:It's successful to create an IP address pool.
[sw1-ip-pool-vlan30]netw
[sw1-ip-pool-vlan30]network 192.168.30.0 mask 24
[sw1]int v
[sw1]int Vlanif 30
[sw1-Vlanif30]dhcp select global
[sw1-Vlanif30]q
[sw1]ip poo
[sw1]ip pool vlan
[sw1]ip pool vlan40
Info:It's successful to create an IP address pool.
[sw1-ip-pool-vlan40]network 192.168.40.0 mask 24
[sw1-ip-pool-vlan40]dns
[sw1-ip-pool-vlan40]dns-list 114.114.114.114
[sw1-ip-pool-vlan40]g
[sw1-ip-pool-vlan40]gateway-list 192.168.40.252
[sw1-ip-pool-vlan40]ex
[sw1-ip-pool-vlan40]excluded-ip-address 192.168.40.100 192.168.40.150
[sw1-ip-pool-vlan40]q
[sw1]int v
[sw1]int Vlanif 40
[sw1-Vlanif40]dhcp select global
[sw1-Vlanif40]q
[sw1]ip poo
[sw1]ip pool v
[sw1]ip pool vlan
[sw1]ip pool vlan50
Info:It's successful to create an IP address pool.
[sw1-ip-pool-vlan50]network 192.168.50.0 mask 24
[sw1-ip-pool-vlan50]g
[sw1-ip-pool-vlan50]gateway-list 192.168.50.252
[sw1-ip-pool-vlan50]dns
[sw1-ip-pool-vlan50]dns-list 114.114.114.114
[sw1-ip-pool-vlan50]ex
[sw1-ip-pool-vlan50]excluded-ip-address 192.168.50.100 192.168.50.150
[sw1-ip-pool-vlan50]q
[sw1]int v
[sw1]int Vlanif 50
[sw1-Vlanif50]dhcp select global
[sw1-Vlanif50]q
[sw1]int vlan
[sw1]ip poo
[sw1]ip pool v
[sw1]ip pool vlan60
Info:It's successful to create an IP address pool.
2.168.60.252
[sw1-ip-pool-vlan60]dns
[sw1-ip-pool-vlan60]dns-list 114.114.114.114
[sw1-ip-pool-vlan60]ex
[sw1-ip-pool-vlan60]excluded-ip-address 192.168.60.100 192.168.60.150
[sw1-ip-pool-vlan60]q
[sw1]int v
[sw1]int Vlanif 60
[sw1-Vlanif60]dhcp select global
[sw1-Vlanif60]q
[sw1]
Sw2dhcp配置：
The device is running!
<sw2>sys
Enter system view, return user view with Ctrl+Z.
[sw2]ip poo
[sw2]ip pool vlan
[sw2]ip pool vlan10
Info:It's successful to create an IP address pool.
[sw2-ip-pool-vlan10]network 192.168.10.0 mask 24
[sw2-ip-pool-vlan10]g
[sw2-ip-pool-vlan10]gateway-list 192.168.10.252
[sw2-ip-pool-vlan10]dns
[sw2-ip-pool-vlan10]dns-list 114.114.114.114
[sw2-ip-pool-vlan10]ex
[sw2-ip-pool-vlan10]excluded-ip-address 192.168.10.100 192.168.10.150
[sw2-ip-pool-vlan10]q
[sw2]int v
[sw2]int Vlanif 10
[sw2-Vlanif10]dhcp select global
Error: Please enable DHCP in the global view first.
[sw2-Vlanif10]q
[sw2]dh
[sw2]dhcp enn
[sw2]dhcp en
[sw2]int Vlanif 10
[sw2-Vlanif10]dhcp select global
[sw2-Vlanif10]q
[sw2]ip poo
[sw2]ip pool vlan
[sw2]ip pool vlan20
Info:It's successful to create an IP address pool.
[sw2-ip-pool-vlan20]network 192.168.20.0 mask 24
[sw2-ip-pool-vlan20]dns
[sw2-ip-pool-vlan20]dns-list 114.114.114.114
[sw2-ip-pool-vlan20]dns
[sw2-ip-pool-vlan20]dns-list 114.114.114.114
Error:Part of the domain-name-server IP has already exist.
[sw2-ip-pool-vlan20]dis
[sw2-ip-pool-vlan20]display th
[sw2-ip-pool-vlan20]display this
#
ip pool vlan20
network 192.168.20.0 mask 255.255.255.0
dns-list 114.114.114.114
#
return
[sw2-ip-pool-vlan20]g
[sw2-ip-pool-vlan20]gateway-list 192.168.20.252
[sw2-ip-pool-vlan20]ex
[sw2-ip-pool-vlan20]excluded-ip-address 192.168.20.100 192.168.20.150
[sw2-ip-pool-vlan20]q
[sw2]ip pool v
[sw2]ip pool vlan30
Info:It's successful to create an IP address pool.
[sw2-ip-pool-vlan30]network 192.168.30.0 mask 24
[sw2-ip-pool-vlan30]dns
[sw2-ip-pool-vlan30]dns-list 114.114.114.114
[sw2-ip-pool-vlan30]g
[sw2-ip-pool-vlan30]gateway-list 192.168.30.252
[sw2-ip-pool-vlan30]ex
[sw2-ip-pool-vlan30]excluded-ip-address 192.168.30.100 192.168.30.150
[sw2-ip-pool-vlan30]q
[sw2]int v
[sw2]int Vlanif 30
[sw2-Vlanif30]dhcp select global
[sw2-Vlanif30]q
[sw2]ip pool vlan40
Info:It's successful to create an IP address pool.
[sw2-ip-pool-vlan40]network 192.168.40.0 mask 24
[sw2-ip-pool-vlan40]g
[sw2-ip-pool-vlan40]gateway-list 192.168.40.252
[sw2-ip-pool-vlan40]dns
[sw2-ip-pool-vlan40]dns-list 114.114.114.114
[sw2-ip-pool-vlan40]ex
[sw2-ip-pool-vlan40]excluded-ip-address 192.168.40.100 192.168.40.150
[sw2-ip-pool-vlan40]q
[sw2]int v
[sw2]int Vlanif 40
[sw2-Vlanif40]dhcp select global
[sw2-Vlanif40]q
[sw2]ip poo
[sw2]ip pool v
[sw2]ip pool vlan50
Info:It's successful to create an IP address pool.
[sw2-ip-pool-vlan50]netw
[sw2-ip-pool-vlan50]network 192.168.50.0ma
[sw2-ip-pool-vlan50]network 192.168.50.0 ma
[sw2-ip-pool-vlan50]network 192.168.50.0 mask 24
[sw2-ip-pool-vlan50]g
[sw2-ip-pool-vlan50]gateway-list 192.168.50.252
[sw2-ip-pool-vlan50]dns
[sw2]ip pool vlan60
Info:It's successful to create an IP address pool.
[sw2-ip-pool-vlan60]netw
[sw2-ip-pool-vlan60]network 192.168.60.0 ma
[sw2-ip-pool-vlan60]network 192.168.60.0 mask 24
[sw2-ip-pool-vlan60]g
[sw2-ip-pool-vlan60]gateway-list 192.168.60.252
[sw2-ip-pool-vlan60]dns
[sw2-ip-pool-vlan60]dns-list 114.114.114.114
[sw2-ip-pool-vlan60]ex
[sw2-ip-pool-vlan60]excluded-ip-address 192.168.60.100 192.168.60.150
[sw2-ip-pool-vlan60]q
[sw2]int v
[sw2]int Vlanif 60
[sw2-Vlanif60]dh
[sw2-Vlanif60]dhcp se
[sw2-Vlanif60]dhcp select g
[sw2-Vlanif60]dhcp select global
[sw2-Vlanif60]q
[sw2]
Telnet远程控制：
R2:
[R2]int v
[R2]int vt
[R2]us
[R2]user-i
[R2]user-interface v
[R2]user-interface vty 0 4(进入vty模式）
[R2-ui-vty0-4]au
[R2-ui-vty0-4]authentication-mode pa
[R2-ui-vty0-4]authentication-mode password （进入配置密码）
Please configure the login password (maximum length 16):wanglong
[R2-ui-vty0-4]us
[R2-ui-vty0-4]user l
[R2-ui-vty0-4]user le
[R2-ui-vty0-4]user pr
[R2-ui-vty0-4]user privilege l
[R2-ui-vty0-4]user privilege level 3（设置权限）
[R2-ui-vty0-4]
[R2-ui-vty0-4]